User Tools

Site Tools


training:sanog35:lab-access

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

training:sanog35:lab-access [2019/12/14 10:58] (current)
philip created
Line 1: Line 1:
 +====== Lab Access Instructions ======
  
 +===== Introduction =====
 +
 +
 +This lab runs on a virtualised environment for Cisco IOS called "​Dynamips"​. ​
 +
 +To join the network which the lab environment is on, associate your laptop with the wireless network called **IPv6**. The password for this network is **6666666666** - this is ten times the number **6**.
 +
 +The method of access to each virtual router is via Telnet to a specific port on the IP of the machine that runs the virtualization platform. If you don't have "​telnet"​ installed on your laptop (becoming very common on modern operating systems), check the agenda page for links to a client you can use.
 +
 +To access the lab, use telnet to connect to the host ''​lab.ws.sanog''​ on the specified port, for example:
 +
 +  $ telnet lab.ws.sanog 2012  ​
 +
 +
 +
 +===== Dynamips Port to Router Console Map =====
 +
 +
 +^ **Port** ^ **Router** ^
 +| 2001     | TR1        |
 +| 2002     | TR2        |
 +| 2011     | B1         |
 +| 2012     | C1         |
 +| 2013     | P1         |
 +| 2014     | A1         |
 +| 2015     | Cust1      |
 +| 2021     | B2         |
 +| 2022     | C2         |
 +| 2023     | P2         |
 +| 2024     | A2         |
 +| 2025     | Cust2      |
 +| ...      | ...        |
 +| 2061     | B6         |
 +| 2062     | C6         |
 +| 2063     | P6         |
 +| 2064     | A6         |
 +| 2065     | Cust6      |
 +| ...      | ...        |
 +
 +===== Login instructions =====
 +
 +After executing the telnet command, you will see something like the following:
 +
 +  Trying 10.10.0.241...
 +  Connected to 10.10.0.241. ​
 +  Escape character is '​^]'​. ​
 +  Connected to Dynamips VM "​P2"​ (ID 8, type c7200) - Console port
 +
 +
 +Press ENTER at this point. Then, if you see this question:
 +
 +
 +  Would you like to enter the initial configuration dialog? [yes/no]:
 +
 +
 +Answer "​no"​.
 +
 +The router will show some initialization routines, and finally, you will see the default prompt:
 +
 +
 +  Router>
 +
 +
 +You can then go into privileged mode:
 +
 +
 +  Router> enable ​
 +  Router#
 +
 +
 +And then enter configuration mode:
 +
 +
 +  Router# configure terminal
 +  Router(config)#​
 +
 +
 +And you are ready to start entering configuration statements. When you are done, exit configuration mode by typing *end* or pressing *ctrl-Z* and save your changes:
 +
 +
 +  Router(config)#​ end
 +  Router# write memory
 +
 +[[:​training:​sanog35:​agenda| Back to Agenda page]]
training/sanog35/lab-access.txt ยท Last modified: 2019/12/14 10:58 by philip